CP6500-V - Kontron CP6500-V CPCI/PICMG 2.16 CPU Board | Supports ULV Celeron...
- Part Number:
- CP6500-V
- Model Number:
- CP6500-V
- Make:
- KONTRON
- Lead Time:
- Available
- Qty In Stock:
- Available
Kontron CP6500-V CPCI/PICMG 2.16 CPU Board | Supports ULV Celeron (256KB L2 Cache) 400MHz Microprocessors Simple Type: CPU Board
For Resellers and High Volume Orders:
Please request a quote to obtain preferred pricing.
Features
- 2xFastEthernet on FP (or PICMG 2.16), VGA, 2x USB
- CPCI/PICMG 2.16 cost optimized value oriented design
- Low Power Celeron® 400MHz
- Optional REAR I/O support
- PMC + onboard HDD + CompactFlash configuration possible
- Scalable memory size up to 512 MByte SDRAM
- Single slot 4HP CPU with passive cooling
Specifications
- Channel: PICMG 2.0 Rev. 3.0 compatible, 32 bit/33 MHz. 5V default signaling (3.3V on request available), REQ/GNT for 7 slots Operating in system slot as system master and in peripheral slot in PCI passive mode (no communication to CompactPCI bus).
- Connector: Ethernet: 2x 10/100Base-TX Ethernet controller based on the Intel 82551ER Ethernet 32-bit PCI bus controller. The two ports can be configured as front or rear I/O (PICMG 2.16). VGA: Intel 82815 GMCH internal VGA controller providing 2D/3D graphics accelerator, 1280x1024x16/75Hz or 1200x1600x256/60Hz analog output. USB: 4x USB2.0 channels up to 480Mbit/s from ICH4, 2x as front I/O, 2xas rear I/O PS/2: PS/2 for keyboard onboard or rear I/O and mouse legacy support on rear I/O COM: 2x serial ports - COM1/2 - default RS232, optionally RS485/RS422 COM1 on front I/O or both on rear I/O IDE: Two EIDE interfaces, UltraDMA/100. Primary port: UltraDMA/100 routed to CompactFlash socket and 44-pin, 2mm connector for onboard EIDE 2.5" HDD mounting option Secondary port: UltraDMA/100 40-pin, 2.54mm connector onboard and optional on rear I/O
- Cooling: CompactPCI Core Specification PICMG 2.0 Rev. 3.0 CompactPCI Hot Swap Specification PICMG 2.1 R2.0 CompactPCI Packet Switching Backplane PICMG 2.16 R1.0 Designed to meet or exceed: Safety: UL 1950, UL 94, CSA 22.2 No 950, EN 60950, IEC 950 EMI/EMC: EN 55022 / EN 55024, EN 50081-1 / EN 6100-6-2
- Environment: Operating temp.: 0 oC to +60 oC standard Storage temp.: -55 oC to +85 oC Climatic Humidity: non condensing 93% at 40 C (acc. to IEC 60068-2-78) Altitude: 50,000 ft. (15,240 m)
- Environmental: Front I/O Rear I/O Onboard Connector Total Video: 1 1 - 1 USB: 2 2 - 4 Serial: 1 2 - 2 PS/2 Mouse: - 1 - 1 PS/2 Keyboard: - 1 1 1 Ethernet: 2 2 - 2 ATA100: - 1 2 2 CompactFlash: - - 1 1 PMC: 1 via J4 Pn1-Pn3 1 Floppy: - 1 - 1
- Max Data Transfer Rate: 100 MHz memory speed, Intel 82815 GMCH: Up to 512 MB SDRAM memory without ECC on one 144-pin SODIMM socket, smallest memory size 128 MB Onboard 2.5" HDD mounting CompactFlash socket type II 1MB Firmware Hub for BIOS 8KByte EEPROM for CMOS data storing (for no-battery operation)
- Max. Speed: AMI BIOS with POST codes, setup console redirection to serial port (VT100 mode) with CMOS setup access, BIOS parameters saved in EEPROM, diskless, keyboardless, videoless operation LAN boot support. Board identification number accessible via EEPROM. Ethernet channels switchable via software. Support for Windows 2000, XP, XP Embedded, Linux xVWorks
- Memory: Dimensions: 100mm x 160mm Weight: 320g / 4HP MTBF: tbd
- Miscellaneous: COM1: 9-pin D-Sub (RS232, RS422, RS485) VGA: 15-pin D-Sub VGA connector Ethernet: 2x RJ-45 USB: 2x 4-pin connectors PMC: opening for PMC front panel LEDs: 2x LAN activity (yellow) and speed (green) 1x blue LED for hot swap, 1x watchdog, 1x thermal control 8-LED-field for BIOS POST code or general purpose Reset: reset button, guarded
- OS: Support for all signals to allow peripheral boards to be hot swapped. The individual clocks for each slot and access to the backplane ENUM# signal comply with the PICMG 2.1 Hot-Swap specification.
- PCI: One 32-bit / 33MHz PMC slot Pn1-Pn3, rear I/O Pn3 to J4. 5 V and 3.3 V PCI voltage (default configuration 5V).
- Power Requirement: +5V/4W, +3.3V/6W, max. 12W at 400MHz +5V/8W, +3.3V/6W, max. 17W at 1.0Hz +12V / -12V not used
- Processor: Low voltage Celeron , Micro-FCBGA 478, 256KByte L2 on-die cache: 400MHz ULV Celeron ultra low power dissipation 1GHz LV Celeron high performance All processor versions with passive heat sink. Depending on the processor version forced air cooling at a specific flow rate might be required in the chassis.
- Socket: Watchdog, software configurable, 125 msec to 256 sec. in 12 steps, generates IRQ, NMI or hardware reset, two stage configuration for NMI and Reset. Hardware monitor Winbond W83627 for thermal control, fan speed and all onboard voltages. ICH4 internal RTC (MC146818 compatible), RTC and 256 Byte CMOS RAM with backup, battery replaceable.
- System Monitor: Two IDE connectors supporting Ultra DMA, one 40pin/2.54mm, one 44 pin/2mm for onboard 2.5 HDD or Flash module CompactFlash type II socket 22-pin connector with all LPC signals PS/2 5-pinrow keyboard connector 1x144-pin SODIMM connectors 3x 64-pin PMC interface
- Wake On LAN: J3: PICMG 2.16, VGA, COM1/2, keyboard, mouse, USB3/4 J4: PMC rear I/O J5: IDE (secondary), Floppy
Applications
- None Available
Aliases
- None Available
